詳細內容：PBT/6129C/美國杜邦/PBT+ASA/Ultradur/S4090G6/LS德國巴斯夫POM/Kepital/F10-03H/韓國工程塑料PA6/C38FKS德國朗盛PA66/UVPOM/300PE/美國杜邦PBT/CE7300/日本寶理PA12/Rilsamid/AESN/法國阿科瑪POM/EC-600B/LG化學PA66/70G35EF/美國杜邦/POM/Iupital/F10-02/日本三菱POM/CF452/日本旭化成PA6/N24-LG6荷蘭DSMPOM/N109-LD/LG化學PA6/K222-KMV5荷蘭DSMPOM/M90-45/日本寶理PA6/1013G10-1荷蘭DSMPBT/Celanex/3200-2FC/美國塞拉尼斯PA6/B3UM6PBT/Celanex/LW2547W/美國塞拉尼斯PA66/U328/日本東麗PA6/CM1041LO日本東麗POM/Ultraform/W23200035LEV/德國巴斯夫PA66/A3LHPUVPOM/CP15X/日本寶理POM/M90-44/馬來西亞寶理PA12/UBESTA/3020X8/日本宇部PA6/PX10323/沙伯基礎POM/Hostaform/EC140XF/美國塞拉尼斯POM/TG-61/韓國工程塑料PA6/XP32-E1荷蘭DSMPA66/NY66HI/沙伯基礎（原GE）POM/7467/美國杜邦POM/Celcon/UV140LG/美國塞拉尼斯PA66/RF004S/沙伯基礎PA66/A218 PBT/6129C/美國杜邦 PBT/6129C/美國杜邦 The molding temperature of LCP plastic material is high. Because of its variety, the melting temperature is within the range of 300~425 C. The viscosity of LCP melt is low, the fluidity is good, and it is similar to the olefin plastic. LCP has a very small coefficient of linear expansion and a good dimensional stability. The forming processing conditions are as follows: molding temperature 300~390 C, mould temperature 100~260 C, molding pressure 7~100MPa, compression ratio 2.5~4, and molding shrinkage rate 0.1~0.6. 1. barrel temperature Generally, the temperature of the barrel, the temperature of the nozzle and the melting temperature of the material are shown as shown in the table. If the service life of the screw is taken into account, the temperature difference between the rear, the middle and the front can be reduced. In order to prevent the nozzle salivation, nozzle temperature than shown in the table of the low temperature of 10 DEG C, if you want to improve the liquidity, the temperature can be shown in the table than the temperature higher than 20 DEG C, but must pay attention to the following circumstances. When the barrel temperature is lowered, the detention time is too long, which will not cause the aging of granular material in the container and no corrosive gas. Therefore, there will be no big problems if the residence time is long. However, if the molding is interrupted for a long time, please reduce the temperature of the barrel. When it is re formed, it is good to throw out a few models. Barrel temperature (centigrade) for each grade molding PBT/6129C/美國杜邦PA12/Rilsamid/AESN/Noir/P201/TL/法國阿科瑪PA12/1258/贏創德固賽PBT/DURANEX3105A/日本寶理PBT/Celanex/4306UV/美國塞拉尼斯PBT/KR4001/德國巴斯夫PET/PBT/ENH8560/Resin/沙特sabicPA12/Grilamid/L25W40X/瑞士EMSPOM/HI-525/LG化學PA12/Rilsamid/AZM/30/Gris/632/TLD/法國阿科瑪PBT/BT262/韓國工程塑料POM/510GR/美國杜邦PA6/C218MZ20V10法國羅地亞PA12/TR55LY/瑞士EMSPC+PBT/Lupox/TE5011韓國LGPA12/UBESTA/3030JI14L/日本宇部PA6/BRZ347W瑞士EMSPBT/1400G3/臺灣南亞PA6/K224-G8U荷蘭DSMPA6/PF00C/沙伯基礎（原GE）PBT/310/沙伯基礎（原GE）POM/Hostaform/MR130ACS/美國塞拉尼斯PA66/RV008E/沙伯基礎PBT/XFR6842GF10/泰科納PBT+PET/Lupox/SG3180S韓國LGPBT/TE-5000G/韓國LGPA66/RF007ES/沙伯基礎POM/Celcon/MR25B/美國塞拉尼斯PA6/B3M6PBT/Ultradur/B4406G6/Q717/德國巴斯夫POM/Tenac/CCF452/日本旭化成PBT/T06200/荷蘭DSMPOM/C9021GV3/10/泰科納PA66/RX98372H/沙伯基礎PBT/EE4401F/韓國LGPBT/GP1000H/韓國LG PBT/6129C/美國杜邦 PBT/6129C/美國杜邦 PA6 PA6, also known as nylon 6, is a translucent or opaque milky white particle. It has the characteristics of thermoplastic, light weight, good toughness, good chemical durability and so on. It is widely used in automotive parts, mechanical components, electronic and electrical products, engineering accessories and other products. 1.1 brief introduction 2.2 processing technology 3.3 basic characteristics 4. after PA6 and PA66 5.4 application range brief introduction Name: polyamide 6 or nylon 6 (PA6) Character: semitransparent or opaque milk white crystalline polymer Characteristics: thermoplastic, light quality, good toughness, good chemical resistance and durability Combustion identification method: blue bottom yellow flame, plant flavor Solvent experiment: cyclohexanone and aromatic solvents Density: (g/cm3) 1.14-1.15 Balance water absorption: 3.5% It has good wear resistance, self lubrication and solvent resistance. Tensile strength: > 60.0Mpa Elongation: > 30% Bending strength: 90.0Mpa Notch impact strength: > 5 (KJ/m2) Processing technology Basic characteristics PA66 is anti - soluble for many solvents, but is weak in resistance to acids and other chlorinating agents. PBT/6129C/美國杜邦PA66/A3EG6PA6/BG30XFN01德國朗盛PBT/c5315/日本寶理PBT/600JP/日本寶理PA6/BG-40FC瑞士EMSPA6/LE60LM法國阿科瑪PA12/VESTAMID/EE47-S3/德國贏創(德固賽)PA66/1300SPA6/B3GM35PBT/TXG510/荷蘭DSMPBT/POCAN/A3121/德國朗盛PA66/A3EG7PBT/ST830FRUV/美國杜邦PA6/B3EG3PA12/UBESTA/3020X15/日本宇部PA6/SX218V60法國羅地亞PBT/1110/臺灣南亞PC+PBT/Lupox/HI2303韓國LGPA6/B35FKA德國朗盛PBT/2002k/日本寶理POM/Tenac/CZ4520/日本旭化成PBT/ct7640/日本寶理PA66/SE15CPBT/B-4520/德國巴斯夫PA66/A20V15PA66/CM3304-V0/日本東麗PBT/WFP36/compound/沙伯基礎PA12/VESTAMID/EE40-S3/德國贏創(德固賽)POM/Hostaform/XT90/美國塞拉尼斯PA6/C216法國羅地亞PBT/CELANEX6400/日本寶理POM/LA543/日本旭化成PBT/DURANEX/457EV/日本寶理PBT/Celanex/5214/美國塞拉尼斯POM/Celcon/MC90-HM/美國塞拉尼斯 PBT/6129C/美國杜邦 PBT/6129C/美國杜邦 PA66 Catalog 1.1 use 2.2 injection molding process 3.3 defect treatment 4.4 physical property table purpose Injection speed: High speed (reinforced slightly lower). The runner and gate: because PA612r solidification time is very short, the gate location is important. The aperture not less than 0.5*t (where t is the thickness of plastic parts). If the use of hot runner, gate size should be smaller than the use of conventional channels, because of the hot runner can help to prevent premature freeze. If you dive into the gate, the minimum diameter of the gate should be 0.75mm Defect treatment Resolvent： 1. Check whether the raw materials are wet or mixed with other materials 2. Check whether the raw material is decomposed in the barrel (barrel temperature) Too high, the screw speed is too fast) 3. Check whether the nozzle hole is too small 4. Check whether the model temperature is too low 5. Bad die exhaust 6. Whether the size of the gate is too small 7. The back pressure is too low and the recycled material is too much The solution of weld mark in the processing of nylon 612 products: The mechanism is that the low bonding temperature is very low at the end of the flow at the end of the flow, so that the combination of the two strand flows is not close. Resolvent： 1. Increase the pressure and speed of injection 2. Improve the mold temperature 3, improve the temperature of the material 4. Improve the mold The solution of the exhaust and shrinkage of the nylon 612 products during processing: The mechanism is the injection or shrinkage of the product. If it was solved by injection molding If it is to shrink the water, the solution is solved. The solution of the focal spot produced during the processing of nylon 612 products: The mechanism is that when the injection speed is high, the rubber cavity will occupy the mold cavity at high speed. When the gas in the mold cavity is not enough to exclude, the gas will be compressed and the product will be scorched after the gas is compressed.